P.O. Box 36795
Tucson, Arizona 85740
MATERIAL
SAFETY DATA SHEET
For
more specific details contact J D Russell Company Corporate Offices at
520 742-6194
GENERAL INFORMATION
| PRODUCT NAME: ANCHOR BOLTS |
Creation Date: 3/10/00
|
PRODUCT IDENTIFICATION
|
IDENTIFICATION
NAME: STEEL
|
|
|
|
|
Mild
Steel Grades:
|
|
Formula:
|
N/A
|
|
Chemical
Name & Synonyms
|
N/A
|
Chemical
Family
|
N/A
|
TYPICAL
CHEMICAL COMPOSITION
|
N/A
|
PHYSICAL DATA
|
Physical
State:
|
Solid
|
Specific
Gravity:
|
7.6
– 7.8
|
|
Appearance
and Odor:
|
Gray
Metal: Odorless
|
Vapor
Pressure:
|
N/A
|
|
Boiling
Point:
|
N/A
|
Vapor
Density
|
N/A
|
|
Melting
Point:
|
|
Evaporation
Rate:
|
N/A
|
|
Solubility
in Water:
|
N/A
|
%
Volatile by Volume:
|
N/A
|
|
Ph:
|
N/A
|
|
|
HAZARDOUS INGREDIENTS / SARA III INFORMATION
| This product does not meet the criteria of a hazardous chemical as defined by the Federal Occupational Safety and Health Hazard Communication Standard (29 CFR 1910.1200). This form is being provided solely as general information and should not be construed as a determination that the product is a hazardous chemical. |
FIRE AND EXPLOSION HAZARD DATA
|
Flash
Point:
|
N/A
|
|
Flammable
limits in air by volume:
|
Non
Flammable
|
|
Extinguishing
Media:
|
Non
Flammable or explosive
|
|
Special
Firefighting Procedures:
|
Steel
Products in the solid state present no fire or explosive hazard
|
|
Unusual
Fire and Explosion Hazards:
|
N/A
|
|
Revision
Date: 041200
|
MATERIAL
SAFETY DATA SHEET
Page
2 of 2 Anchor Bolts 3/10/00
HEALTH HAZARD DATA
|
Threshold
Limit Value:
|
N/A
|
|
Effects
of Overexposure:
|
Exposure
to the constituents of these products will only occur during activities
such as welding or burning. However, because of the low toxicity of the
components and / or the low air levels anticipated during such activities,
these products are not considered to be hazardous chemicals as defined
by the federal OSHA Hazard Communication Standard.
|
REACTIVITY DATA
|
Stability:
|
This
material is stable
|
|
Conditions
to avoid:
|
Contact
with acids
|
|
Incompatibility
(Materials to Avoid):
|
|
|
Hazardous
decomposition or byproducts:
|
Fumes
and / or gases produced from welding or burning operations
|
|
Hazardous
Polymerization:
|
Will
not occur
|
SPILL OR LEAK PROCEDURES
|
Steps
to be taken in case material is released or spilled:
|
N/A
|
|
Waste
Disposal Method:
|
Any
excess product can be recycled for further use or disposal by methods which
are in accordance with local, state, and federal regulations.
|
SPECIAL PROTECTION INFORMATION
|
Respiratory
Protection: (When cutting, grinding, or welding)
|
Remove
from excessive exposure levels unless proper respiratory protection is
worn.
|
||
|
Ventilation:
|
Yes
|
Local
Exhaust
|
Sufficient
to maintain exposure levels
|
|
Protective
Gloves:
|
Not
required
|
Special:
|
N/A
|
|
Eye
Protection:
|
Not
anticipated to pose a significant eye hazard
|
||
|
Other
Protective Equipment:
|
Unless
cutting, welding, or grinding – glasses not recommended
|
||
SPECIAL PRECAUTIONS
|
Precautions
to be taken in handling and storing:
|
Maintaining
air levels of iron oxide fume and dusts below its T.L.V. should be sufficient
to control for airborne concentrations other constituents.
|
|
Other
Precautions:
|
Use
fork truck or mechanical conveyance to avoid lifting injuries
|
|
DISCLAIMER:The
information provided in this MSDS Sheet was obtained from sources, which
we believe are reliable.However,
the information is provided without any representation or warranty, expressed,
or implies regarding the accuracy or correctness.
|
|
|
The
conditions or methods of handling, storage, use and disposal of the products
are beyond our control and may be beyond our knowledge.For
this and other reason, we do not assume any responsibility and expressly
disclaim liability for loss, damage, or expense arising out of or in any
way connected with the handling, storage, use or disposal of the product.
|
|